CGI Custom & Geometric Windows Nationwide | Sightline Windows & Doors Pinecrest

CGI Custom & Geometric Windows in Pinecrest: What to Know First

As an independent CGI service provider, we measure, order, and install CGI custom and geometric windows across Pinecrest with written prices that match the final invoice. Most custom CGI shapes - arched tops, trapezoids, oversized fixed units - run $2,800 to $7,400 installed depending on series and impact rating, with measured surveys completed within 48 hours of your call. We don’t do verbal estimates; Haven Clause 1 means the document you sign is the document you pay.

Call (786) 442-3200

This page is for Pinecrest homeowners who already own CGI windows and need custom shapes for an addition, replacement, or renovation, or who are comparing CGI against other impact-rated lines for a new geometric opening. Call (786) 442-3200 to schedule your free measured survey.

How CGI Products Fail - and How We Fix Them

• Sentinel by CGI arched windows: seal failure in the thermal break. The curved aluminum extrusion in the Sentinel series creates stress concentration at the crown of the arch where the polyamide thermal break meets the glazing pocket. In Pinecrest’s salt-air environment, that junction corrodes faster than straight-leg frames. We see this on homes east of Red Road where the afternoon easterly carries Biscayne Bay salt. Our fix: we pull the sash, document the corrosion pattern with photos you keep, and replace with OEM thermal-break assemblies rather than field-bending standard stock, which voids the CGI warranty.
• Impact-rated geometric units: laminated glass delamination at the sightline. CGI’s impact-rated custom shapes use SentryGlas or PVB interlayers depending on the series. The 4120 series with PVB is prone to edge delamination when the geometric cut creates a non-uniform edge distance - common in trapezoid units where the fabricator didn’t maintain the 3/4-inch minimum the glazing spec requires. We measure edge distance with a digital caliper, reject out-of-spec units before they leave the shop, and specify SentryGlas for any shape with an acute angle under 45 degrees.
• Sparta series fixed geometric windows: water intrusion at the weep channel. Sparta’s snap-in glazing bead simplifies field installation but the weep slots in custom shapes are often drilled off-center by third-party fabricators. Water backs up into the sill track during Pinecrest’s summer deluges - we logged 14 inches in a three-day stretch last August. We clear the channels with compressed air and a borescope, then redrill to CGI’s pattern using the OEM template so drainage matches the engineered flow rate.
• Custom radius windows: argon loss through curved spacer seams. CGI’s standard straight-line Super Spacer works fine until you bend it to a radius under 24 inches. The butyl seal cracks at the splice, argon escapes, and the U-factor degrades from 0.30 to 0.38 or worse. We specify Warm Edge TGI spacers for tight-radius work, which flex without splicing, and we verify gas fill with a Sparklike handheld analyzer before the unit leaves our shop.
• Oversized CGI fixed units: structural deflection in the head jamb. Custom shapes over 60 inches wide in the Estate series need steel reinforcement that some installers omit to save cost. The head bows, the sash binds, and the locking hardware tears out of the keeper. We calculate dead load and wind load per ASCE 7-22 for Pinecrest’s 170 mph design wind speed, specify the reinforcement schedule in writing, and install with structural screws at 8-inch centers - not the 16-inch spacing we see on failed jobs we get called to correct.

Our CGI Custom & Geometric Windows Process

1. 1
   Measured survey you keep. Sonia Raman or a senior tech arrives with a digital measuring system accurate to 1/16 inch. You get the printout before we leave. No “we’ll email it later.”
2. 2
   Shop drawing review. We read CGI’s fabrication drawings the way Sonia reads them - fast, and with an opinion. We flag any deviation from the approved submittal before the unit enters production.
3. 3
   OEM or verified aftermarket parts decision. For warranty-active units, we use CGI factory parts. For out-of-warranty geometric shapes where CGI lead times stretch past 14 weeks, we source from Miami-area fabricators we’ve vetted for dimensional tolerance and impact certification - documented, not guessed.
4. 4
   Installation with photo record. Every step: rough opening, flashing integration, shim placement, fastener schedule, final sightline check. You get the photo folder by email the same day.
5. 5
   Operational test and written sign-off. We cycle the sash, check the lock engagement depth with a feeler gauge, and verify the weep flow with a water test. You sign the completion document; we don’t leave until you do.
6. 6
   365-Day Done Right Promise activation. The warranty document is in your hand before we pack the tools. If the sightline shifts, the seal fails, or the lock drags, we return under Haven Clause 5: No surprises.

Before

After

What CGI Custom & Geometric Windows Costs in Pinecrest

What moves the price: impact rating (HVHZ vs. non-impact), glass make-up (SentryGlas vs. PVB), reinforcement needs, and whether the existing frame can be retained or needs full replacement. Pinecrest’s 170 mph wind zone means every custom shape must carry a Miami-Dade NOA or Florida Product Approval - we verify this before quoting, not after.

Call (786) 442-3200 for your free measured survey. The written price you receive is the invoice price. Measure twice. Quote once. No surprises at the invoice.

Why Pinecrest Homeowners Call Sightline Windows & Doors Pinecrest for CGI Work

We’ve installed and serviced CGI products in Pinecrest since 2012, including full-frame replacements in the Banyan Drive corridor where original single-pane aluminum from the 1970s still shows up in older homes. Our crew knows which CGI series used which glazing system by production year, and we carry PGT, CWS, ES Windows, and ECO Window Systems as alternatives when a custom shape isn’t viable in the CGI line or the lead time doesn’t work for your project.

Haven Clause 3 means the technician at your door is background-checked, uniformed, and identified by license number before arrival - the same person on the record. Haven Clause 4 means you get the photo evidence. And the 365-Day Done Right Promise is stamped on every job, not offered as a courtesy when something goes wrong.

FAQs