Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Therma-Tru Sliding & Patio Doors: The Pinecrest Owner’s Guide
We stock and install Therma-Tru-compatible sliding and patio door systems in Pinecrest, with typical installed replacement costs running $2,800 to $6,400 depending on frame material, glass package, and whether the opening needs structural adjustment. Most Therma-Tru track assemblies, roller carriages, and multipoint lock hardware are available same-day through our Miami-Dade supply chain. Homeowners usually discover a problem when the door sticks in the track during summer humidity, the rollers grind instead of glide, or the multipoint lock no longer draws the panel tight against the weatherstrip - often after years of Florida’s salt air and UV exposure have corroded the bottom rail or flattened the roller profile.
Which Therma-Tru Models This Applies To
Therma-Tru organizes its sliding and patio door offerings into distinct series, and the parts are not cross-compatible. The Contemporary Collection uses a 2-1/4 inch bottom rail with sealed stainless-steel roller carriages rated for 250 lb. per panel; the Classic-Craft and Fiber-Classic lines run a taller 3-1/8 inch rail with heavier-duty tandem rollers. The Impact-Rated series, required in Miami-Dade and Broward wind-borne debris zones, uses reinforced interlocking stiles and a proprietary multipoint lock with a 45 mm backset - not the standard 35 mm found on non-impact units.
To identify your model, check the etched specification label on the glass corner or the hinge-side jamb sticker. We need the series name, nominal panel size, and whether the unit is impact-rated or non-impact. For hardware-only replacement, we source OEM Therma-Tru components through our distributor; for track or frame damage, we often specify a compatible heavy-duty aftermarket roller assembly from K.N. Crowder or slide-co, which carries the same load rating at roughly 60 percent of OEM cost. The aftermarket route makes sense when the original track is intact and only the carriage has failed. When the aluminum track itself is grooved or corroded - common in Pinecrest homes within two miles of the coast - we replace the full track cap and rail assembly to prevent premature recurrence.
Signs Your Therma-Tru Sliding & Patio Doors Is Failing

- The panel drags or requires shoulder force to move. This usually means the roller carriage bearings have seized or the roller diameter has worn below 1-1/8 inch, the minimum effective diameter for Therma-Tru’s standard track geometry. In Pinecrest, we see this accelerate where irrigation spray hits the bottom rail repeatedly, washing out lubrication and introducing grit.
- Visible gap between the panel and jamb when “closed,” or light leaking through the lock side. The multipoint lock’s hook bolts or shoot bolts are no longer engaging fully, often because the keepers have shifted in the jamb or the lock faceplate has compressed the weatherstrip over time. On impact-rated units, this also compromises the pressure-equalization seal.
- Water pooling on the interior track during heavy rain. The weep holes in the sill track are clogged with organic debris, or the sill pan flashing was never properly integrated with the stucco drainage plane - a detail we find missing in roughly one-third of Pinecrest installations from the 2005-2015 construction wave.
- Condensation between the glass panes. The insulated glass unit (IGU) seal has failed, allowing moist Florida air into the airspace. Therma-Tru uses a dual-seal system with PIB primary and silicone secondary; once the edge seal breaches, the Low-E coating and argon fill are compromised and the IGU must be replaced, not repaired.
- The handle set spins freely or the thumb latch does not return. The internal spindle or spring cassette in the handle mechanism has fractured. This is a ten-minute part swap if caught early; left unattended, the broken internal pieces can fall into the lock body and require full multipoint replacement.
Before
AfterReplacement Cost & What’s Included
| Component / Scope | Typical Range in Pinecrest |
|---|---|
| Roller carriage replacement (OEM or aftermarket) | $340 - $580 |
| Multipoint lock assembly replacement | $520 - $890 |
| Full panel replacement (non-impact, standard size) | $2,800 - $4,200 |
| Full panel replacement (impact-rated, standard size) | $4,600 - $6,400 |
| Track rail / sill cap replacement with drainage correction | $780 - $1,450 |
| Insulated glass unit (IGU) replacement only | $680 - $1,120 |
The spread reflects three variables: whether the opening is square within 1/4 inch (older Pinecrest homes with settled slab foundations often are not), whether the stucco return needs cutting and patching for frame access, and whether the original installation used proper sill pan flashing - which we correct when we find it absent. Every quote is itemized: parts, labor, disposal, and any structural remediation. The price on the measured survey document is the price on the invoice. Our roller and lock hardware replacements carry a two-year workmanship warranty; full panel installations are covered by the 365-Day Done Right Promise under Haven Clause 5 - No surprises.
DIY or Call Us?

There is one safe check a homeowner can make: vacuum the track thoroughly and flush the weep holes with a thin wire or compressed air. If the door still drags, the problem is below the surface.
We do not recommend homeowner replacement of roller carriages or multipoint locks. The panel must be lifted from the track - a two-person minimum, typically 120 to 200 pounds depending on glass package - and the adjustment screws that set roller height are easily stripped. More critically, improper reinstallation can distort the panel alignment, stress the tempered glass, or leave the multipoint lock misaligned so the hook bolts do not engage the keepers. On impact-rated units, any field modification that disturbs the interlock geometry voids the Miami-Dade product approval.
We carry Therma-Tru-compatible roller assemblies, multipoint lock bodies, and handle sets on our service vehicles. Most hardware replacements in Pinecrest are completed in under two hours. Call (786) 442-3200 to schedule your free estimate - we bring the measured survey, the written price, and the parts.
FAQs
How long do Therma-Tru sliding door rollers last in South Florida?
In Pinecrest’s climate, standard stainless-steel roller carriages typically last 8 to 12 years with basic track maintenance; units within a mile of Biscayne Bay or with chronic irrigation exposure often see 6 to 8 years. The salt air does not directly attack stainless, but the washed-out lubrication and grit infiltration accelerate bearing wear. Call (786) 442-3200 for an exact quote - estimates are free.
Can the multipoint lock be repaired instead of replaced?
Occasionally, if the issue is a single broken spring in the handle mechanism or a loose keeper screw, we repair. If the lock body itself has fractured internal components or the faceplate is distorted from over-torque, replacement is the only reliable fix. We inspect before quoting either path. Call (786) 442-3200 for an exact quote - estimates are free.
How long does a full panel replacement take?
Standard size, straightforward opening: one day for removal, installation, and operational testing. If the stucco return needs cutting, the sill pan needs correction, or the header requires reinforcement for impact-rated hardware, we schedule a second day. We never rush structural detail. Call (786) 442-3200 for an exact quote - estimates are free.
Do you stock Therma-Tru parts, or do you have to order them?
We stock roller carriages, multipoint locks, handle sets, and weatherstrip for the most common Therma-Tru series on our Pinecrest service vehicles. Specialty impact-rated hardware or oversized panel components typically arrive next business day from our Miami-Dade distributor. We confirm availability when you call. Call (786) 442-3200 for an exact quote - estimates are free.
Sightline Windows & Doors Pinecrest is an independent service provider and is not affiliated with Therma-Tru Corporation. We also stock parts for PGT, CGI, and CWS sliding and patio door systems.
Measure twice. Quote once. No surprises at the invoice.
Ready to get a written price before any work starts? Call (786) 442-3200 to schedule your free estimate. Our technician will arrive with a license number you can verify, measure your opening to the sixteenth, and leave you with a documented scope and price that does not change at the invoice.
Written by Sonia Raman, Owner, Sightline Windows & Doors Pinecrest at Sightline Windows & Doors Pinecrest, serving Pinecrest and nearby areas.










Before
After
Before
After
Before
After